Weed Eater Blower 952711849 User Manual

R
Trademark  
Please do not return product to retailer.  
Por favor, no devuelva el producto al lugar de compra.  
Veuillez ne pas retourner le produit au détaillant.  
1--800--554--6723  
Register your product online at:  
Registre su producto en línea en:  
Enregistrez votre produit en ligne à l’adresse :  
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
WEB 200  
FOR HOUSEHOLD USE ONLY  
PARA USO CASERO SOLAMENTE  
POUR UTILISATION À DES FINS  
DOMESTIQUES SEULEMENT  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias  
e instrucciones de seguridad. El no hacerlo puede resultar en  
lesiones graves.  
AVERTISSEMENT:  
Veuillez lire le manuel d’instructions et bien respecter tous les  
avertissements et toutes les instructions de sécurité. Tout défaut  
de le faire pourrait entraîner des blessures graves.  
WEED EATER  
7349 Statesville Road  
Charlotte, NC 28269  
WEED EATER  
850 Matheson Blvd. West  
Mississauga, Ontario L5V 0B4  
545186752 Rev. 2 4/15/10 BRW  
 
gauge. The smaller the gauge number,  
the heavier the cord. (NOTE: The correct  
size to be used depending on the cord  
length is shown in this manual. See SE-  
LECT AN EXTENSION CORD in the AS-  
SEMBLY section).  
WARNING:  
SERVICING OF DOUBLE INSULATED  
BLOWER  
All electrical repairs to this unit, including  
housing, switch, motor, etc., must be diag-  
nosed and repaired by an authorized ser-  
vice dealer. Replacement parts for a  
double insulated appliance must be iden-  
tical to the parts they replace. A double in-  
sulated appliance is marked with the  
words “DOUBLE INSULATION” or “DOUBLE  
INSULATED.” The symbol (square within a  
square) may also be marked on the ap-  
pliance. Failure to have the unit repaired  
by an authorized service dealer can  
cause the double insulation construction  
to become ineffective and result in serious  
injury.  
UNIT/MAINTENANCE SAFETY  
S Do not set the unit on any surface ex-  
cept a clean, hard area while the unit is  
running. Debris such as gravel, sand,  
dust, grass, etc., could be picked up by  
the air intake and thrown out through the  
discharge opening, damaging the unit,  
property, or causing serious injury to by-  
standers or operator.  
S Do not overreach or use from unstable  
surfaces such as ladders, trees, steep  
slopes, rooftops, etc. Use extra care  
when cleaning on stairways. Keep firm  
footing and balance at all times. Keep  
hands out of tubes.  
S Inspect the entire unit before each use  
for worn, loose, missing, or damaged  
parts. Do not use until the unit is in  
proper working order.  
S This unit is double insulated. See the  
DOUBLE INSULATION CONSTRUCTION  
section. Have all internal service per-  
formed by qualified service repair per-  
sonnel to avoid creating a hazard or  
voiding your warranty.  
S Have all maintenance other than the  
recommended procedures described in  
the instruction manual performed by  
your authorized service dealer.  
S Always see your authorized service  
dealer to replace a damaged impeller.  
Parts that are chipped, cracked, broken,  
or damaged in any other way can fly  
apart and cause serious injury. Replace  
damaged parts before using the unit.  
S Never place any object in the air intake  
opening as this could restrict proper air  
flow and cause damage to the unit.  
S Do not use multiple cords.  
S Keep the extension cord clear of operator  
and obstacles at all times.  
S Tie cord to cord retainer and connect to  
recessed plug as shown in this manual to  
prevent damage to unit and/or extension  
cord and to reduce the possibility of the  
extension cord disconnecting from the  
unit during operation.  
S Do not attempt to repair unit. Inspect the  
insulation and connectors on the unit  
and extension cord before each use. If  
there is any damage, do not use until  
damage is repaired by your authorized  
service dealer.  
S Do not use the unit if the switch does not  
turn the unit on and off properly. Have the  
unit repaired by your authorized service  
dealer.  
S Avoid accidental starting. Be sure the  
switch is in the OFF position and keep  
your hand and fingers away from the  
switch while connecting the unit to the  
power source or when carrying a unit con-  
nected to the power source.  
S Avoid any body contact with any  
grounded conductor, such as metal  
fences, or pipes, to avoid the possibility of  
electric shock.  
S Ground Fault Circuit Interrupter (GFCI)  
protection should be provided on the cir-  
cuit or outlet to be used for this unit. Re-  
ceptacles are available having built-in  
GFCI protection and may be used for this  
measure of safety.  
S Stop the motor immediately if you are ap-  
proached.  
DOUBLE INSULATION  
CONSTRUCTION  
This unit is double insulated to help pro-  
tect against electric shock. Double insula-  
tion construction consists of two separate  
“layers” of electrical insulation instead of  
grounding. Tools and appliances built with  
a double insulation system are not in-  
tended to be grounded. No grounding  
means is provided on this unit, nor should  
a means of grounding be added to this  
unit. As a result, the extension cord used  
with your unit can be plugged into any  
standard 120 volt electrical outlet. Safety  
precautions must be observed when op-  
erating any electrical tool. The double in-  
sulation system only provides added pro-  
tection against injury resulting from an  
internal electrical insulation failure.  
3
 
S Never douse the unit with water or other  
liquids or squirt with a water hose. Clean  
the unit using a damp cloth. Wipe off  
with a clean dry cloth. See MAINTE-  
NANCE.  
S Check air intake openings and tubes  
frequently, always with the unit stopped  
and power source disconnected. Keep  
vents and tubes free of debris which can  
accumulate and restrict proper air flow.  
S Do not burn, incinerate, or expose this  
unit to extreme heat.  
S Store the unit unplugged in a high, cool,  
dry, indoor area out of the reach of chil-  
dren.  
S To avoid spreading fire, do not use blow-  
er near leaf or brush fires, fireplaces,  
barbecue pits, ashtrays, etc.  
S Never place objects inside the blower  
tubes; always direct the blowing debris  
away from people, animals, glass, and  
solid objects such as trees, automo-  
biles, walls, etc. The force of air can  
cause rocks, dirt, or sticks to be thrown  
or to ricochet which can hurt people or  
animals, break glass, or cause other  
damage.  
S Never use for spreading chemicals, fer-  
tilizers, or any other substances which  
may contain toxic materials.  
S Use only recommended attachments  
and replacement parts to avoid creating  
a hazard and/or voiding warranty.  
S Maintain the unit according to recom-  
mended procedures.  
STANDARDS  
This product is listed by Underwriters Lab-  
oratories, Inc., in accordance with UL  
Standard 1017.  
If situations occur which are not covered  
in this manual, use care and good judg-  
ment. If you need assistance, contactyour  
authorized service dealer or call  
1--800--554--6723. Failure to follow all  
Safety Rules and Precautions can result  
in serious injury.  
S Use only for jobs explained in the OP-  
ERATION section of this manual.  
BLOWER SAFETY  
S Use only in daylight or in good artificial  
light.  
S Inspect the area before using the unit.  
Remove all debris and hard objects  
such as rocks, glass, wire, etc., that can  
ricochet, be thrown, or otherwise cause  
injury or damage during operation.  
S Never run the unit without the proper  
equipment attached. When used as a  
blower, always install a blower tube. Use  
only recommended attachments. Do  
not use with any opening blocked, Keep  
free of dust, lint, hair and anything that  
may reduce air flow.  
SAVE THESE INSTRUCTIONS  
S To reduce the risk of electrical shock, this  
unit has a polarized plug (one blade is  
wider than the other) and will require the  
use of a polarized extension cord. The  
appliance plug will fit into a polarized ex-  
tension cord only one way. If the plug  
does not fit fully into the extension cord,  
reverse the plug. If the plug still does not  
fit, obtain a correct polarized extension  
cord. A polarized extension cord will re-  
quire the use of a polarized wall outlet.  
This plug will fit into the polarized wall out-  
let only one way. If plug does not fit fully  
into the wall outlet, reverse the plug. If it  
still does not fit, contact a qualified electri-  
cian to install the proper wall outlet. Do not  
change the equipment plug, extension  
cord receptacle, or extension cord plug in  
any way.  
4
 
ASSEMBLY  
D Heavy enough to carry full current from  
WARNING: Stop the unit and dis-  
connect from the power source before  
opening the vacuum inlet cover. The mo-  
tor must be stopped and the impeller  
blades no longer turning to avoid serious  
injury from the rotating blades.  
the power source to the unit. Otherwise,  
loss of power and overheating can oc-  
cur causing damage to unit. Refer to  
table for minimum wire gauge recom-  
mendations. The cord must be marked  
with the proper wire gauge. (Appropriate  
extension cords are available.) Do not  
use multiple cords.  
WARNING: If received assembled,  
ensure your unit is properly assembled  
and all fasteners are secure.  
S A standard screwdriver is required for  
assembly.  
D In good condition. Cord insulation must  
be intact with no cracks or deterioration.  
Plug connectors must be undamaged.  
DO NOT use multiple cords.  
Your blower can also be used as a  
vacuum by purchasing an optional  
vacuum kit (Model EBVA 1910). Con-  
tact your authorized service dealer  
for details.  
BLOWER TUBE ASSEMBLY  
1. Align the grooves on the blower tube  
with the grooves on the bloweroutlet.  
2. Push the blower tube onto theblower  
outlet until it snaps into place (tube is  
secured by red tube release button).  
3. To remove the blower tube, press the  
tube release button while pulling on  
tube.  
MINIMUM WIRE GAUGE  
RECOMMENDATIONS  
VOLTS  
120  
25 FT.  
50 FT.  
100 FT.  
16  
A.W.G.*  
16  
A.W.G.*  
14  
A.W.G.*  
*American Wire Gauge  
Secure the extension cord to the unit by  
threading the cord through the cord re-  
tainer (see illustration). Insert the cord  
receptacle into the recessed plug.  
CAUTION: Failure to use cord retain-  
er could result in damage to the unit,  
extension cord, or both.  
Tube Release Button  
Blower Tube  
Co
Re
Blower outlet  
SELECT AN EXTENSION CORD  
Use only a 120 A.C. voltage supply as  
shown on nameplate of the unit to  
power your blower.  
The extension cord used to reach the  
power source must be:  
sed  
Plug  
Unit  
Co
Re
D Specifically marked as suitable for out-  
door use. The cord mustbe marked with  
the suffix “W”.  
5
 
USING YOUR UNIT  
KNOW YOUR ELECTRIC BLOWER  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR  
UNIT. Compare the illustrations to your unit to familiarize yourself with the location of  
the various controls and adjustments. Save this manual for future reference.  
ON/OFF Switch  
Top Handle  
Tube Release Button  
Blower Tube  
Air Vents  
Cord  
Retainer  
Rear  
Handle  
Inlet Cover  
Latch  
ON/OFF SWITCH  
BLOWER TUBE  
The ON/OFF SWITCH is used to activate  
The BLOWER TUBE is designed to direct  
the motor.  
INLET COVER LATCH  
The INLET COVER LATCH is used toopen  
and close the vacuum inlet cover.  
the flow of air.  
TUBE RELEASE BUTTON  
The TUBE RELEASE BUTTON secures the  
blower tube or elbow tube to the blower  
unit during operation. Also, pressing the  
tube release button allows removal of the  
blower tube or elbow tube.  
USING YOUR UNIT AS A BLOWER  
WARNING: You MUST make sure  
the tubes are secure before using the  
unit.  
WARNING: Inspect the area be-  
fore using the unit. Remove all debris  
and hard objects such as rocks, glass,  
wire, etc., that can ricochet, be thrown,  
or otherwise cause injury or damage  
during operation.  
Use your unit as a blower for:  
D Sweeping debris or grass clippings from  
driveways, sidewalks, patios, etc.  
D Blowing grass clippings, straw, or  
leaves into piles, or removing debris  
from corners, around joints, or between  
bricks.  
Direct air flow by directing the blower  
tube down or to one side. Always work  
away from solid objects such as walks,  
large stones, vehicles, and fences.  
Clean corners by starting in corners and  
moving outward. This will help prevent  
an accumulation of debris which could  
fly into your face.  
WARNING: Do not use the unit  
without the blower tube properly attached  
to avoid flying debris and/or impeller con-  
tact which can cause serious injury. Al-  
ways wear eye protection to preventrocks  
or debris from being blown or ricocheting  
into the eyes and face which can result in  
blindness or serious injury.  
STOPPING YOUR UNIT  
Slide the ON/OFF switch to the OFF  
position.  
STARTING YOUR UNIT  
Your unit has two run positions, LOW  
and HIGH. Slide the switch to one of  
these positions to turn on the unit.  
OPERATING POSITION  
Eye Protection  
Be careful when working near plants.  
The force of the air could damage  
tender plants.  
Blower  
6
 
MAINTENANCE  
CHECK FOR DAMAGED OR  
WARNING: Disconnect power  
WORN PARTS  
source before performing maintenance.  
Contact your authorized service dealer  
for replacement of damaged or worn  
parts.  
GENERAL RECOMMENDATIONS  
The warranty on this unit does not cover  
items that have been subjected to opera-  
tor abuse or negligence. To receive full  
value from the warranty, the operator must  
maintain unit as instructed in this manual.  
Various adjustments will need to be made  
periodically to properly maintain your unit.  
S ON/OFF Switch -- Ensure switch func-  
tions properly by moving the switch to  
the OFF position. Make sure motor  
stops; then restart motor and continue.  
S Inlet Cover -- Discontinue use of unit if  
inlet cover fails to latch properly or if it is  
damaged in any way.  
BEFORE EACH USE  
AFTER EACH USE  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Inlet Cover  
INSPECT AND CLEAN UNIT & LABELS  
Stop unit and unplug extension cord.  
S After each use, inspect complete unit  
for loose or damaged parts. Clean the  
unit using a damp cloth.  
S Blower Tube  
S Wipe off unit with a clean dry cloth.  
STORAGE  
If your blower is to be stored for a period  
of time:  
WARNING: Perform the following  
steps after each use:  
S Stop unit and disconnect from the pow-  
er source.  
S Stop unit and disconnect from the pow-  
er source.  
S Clean the entire unit before lengthy stor-  
age.  
S Inspect the blower and blower tube.  
Close and make sure the cover is  
latched.  
S Allow motor to cool before storing or  
transporting.  
S Store unit with all guards in place. Posi-  
tion unit so that any sharp object cannot  
accidentally cause injury.  
S Clean air vents and air inlet of debris.  
S Store your unit and extension cord in a  
well ventilated area and covered, if pos-  
sible, to prevent dust and dirt accumula-  
tion. Do not cover with plastic. Plastic  
cannot breathe and may cause con-  
densation and eventual rust or corro-  
sion.  
S Store unit unplugged, well out of the  
reach of children.  
SEASONAL STORAGE  
Prepare unit for storage at the end of  
the season or if it will not be used for  
30 days or more.  
S Check entire unit for loose screws. Re-  
place any damaged, worn, or broken  
parts.  
7
 
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect from the power source before  
performing all of the recommended remedies below except remedies that re-  
quire unit to be operating.  
SYMPTOM CAUSE  
Unit fails to 1. Switch in the OFF position.  
REMEDY  
1. Slide switch to ON position.  
2. Reconnect extension cord.  
operate.  
2. Extension cord discon--  
nected.  
3. Reset circuit breaker or  
fuse.  
4. Contact your authorized  
service dealer.  
1. Contact your authorized  
service dealer.  
3. Circuit breaker tripped, or  
fuse blown.  
4. Mechanical failure  
Unit  
vibrates  
abnormally.  
1. Mechanical failure  
Impeller will  
not turn  
freely.  
1. Debris in air intake area.  
2. Mechanical failure.  
1. Clean unit. Remove any debris.  
2. Contact your authorized  
service dealer.  
LIMITED WARRANTY  
WEED EATER, a division of Husqvarna  
Outdoor Products Inc., warrants to the  
original consumer purchaser that each  
new WEED EATER brand electric or  
cordless product is free from defects in  
material and workmanship and agrees to  
repair or replace under this warranty any  
defective WEED EATER brand electric or  
cordless product within two (2) years from  
the original date of purchase.  
If your WEED EATER brand electric or  
cordless product should fail within the lim-  
ited warranty period, you may return it in  
complete condition, prepaid, with proof of  
purchase, to the dealer from whom it was  
purchased for repair or replacement at the  
option of WEED EATER.  
In Canada, contact:  
WEED EATER  
850 Matheson Blvd. West  
Mississauga, Ontario L5V 0B4  
Giving the model number, serial number  
and date of purchase of your product and  
the name and address of the authorized  
dealer from whom it was purchased.  
THIS WARRANTY GIVES YOU SPECIFIC LE-  
GAL RIGHTS, AND YOU MAY HAVE OTHER  
RIGHTS WHICH VARY FROM STATE TO  
STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED, AND  
THERE ARE NO OTHER EXPRESS WAR-  
RANTIES EXCEPT THOSE EXPRESSLY  
STIPULATED HEREIN.  
This warranty is not transferable and does  
not cover damage or liability caused by  
improper handling, improper mainte-  
nance or alteration, or the use of accesso-  
ries and/or attachments not specifically  
recommended by WEED EATER for this  
product. Additionally, this warranty does  
not cover parts that will wear and require  
replacement with reasonable use during  
the warranty period. This warranty does  
not cover predelivery set--up or normal  
adjustments explained in the instruction  
manual.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE LIM-  
ITATIONS OR EXCLUSION MAY NOT APPLY  
TO YOU.  
This is a limited warranty within the  
meaning of that term as defined in the  
Magnuson--Moss Act of 1975.  
The policy of WEED EATER is to contin-  
uously improve its products. Therefore,  
WEED EATER reserves the right to  
change, modify, or discontinue models,  
designs, specifications, and accesso-  
ries of all products at any time without  
notice or obligation to any purchaser.  
Should you have any unanswered ques-  
tions concerning this warranty, please  
contact:  
WEED EATER, a division of  
Husqvarna Outdoor Products Inc.  
7349 Statesville Road  
Charlotte, NC 28269  
1--800--554--6723  
8
 

Teac Headphones CT H02 User Manual
Texas Instruments Stereo System ADS8402 EVM ADS8412 EVM User Manual
Timex Watch 359 095002 EU User Manual
ToCAD Camcorder Accessories PRO 723B User Manual
Toshiba Digital Camera PDR M11 User Manual
Tricity Bendix Washer Dryer WDR 1030 User Manual
Tripp Lite Indoor Furnishings UPSHDEARKIT User Manual
Troy Bilt Lawn Mower J860 User Manual
Uniflame Fire Pit GAD1200B User Manual
Vinotemp Refrigerator VT WINEDISP4 User Manual